Seceuroglide Centre Ribbed Design (26 Colour and Finish Options) Insulated Sectional Door garage door Steel Seceuroglide

The Seceuroglide Sectional Garage Door creates a stylish feature that is sure to enhance the look of your home but also the security and insulation. The Centre Ribbed sectional garage door by Seceuroglide is a timeless design that can be styled many different ways. The diverse range of available finishes mean this ribbed design could fit in with a very modern garage, or it could be styled in a traditional setting, mimicking a timber door.

The Seceuroglide sectional garage door has a 40mm thick insulated steel panel manufactured to the highest specification, filled with PU foam - this along with the high grade rubber weather seals on all sides ensures a very high level of insulation, meaning an energy efficient and money saving door. This also goes hand-in-hand with security - the thick panels and the sophisticated locking system ensures peace of mind for you and your whole family. Whether you have a manual or an automated door you will be totally protected from intruders.

The Sectional garage door design makes the most of your driveway and garage; vertical operation ensures you can park right up to your door on either side and use your entire driveway. The Elite requires just 130mm headroom for motorised operation and 100mm for manual operation.

There are two free of charge standard finishes; a traditional style White woodgrain embossed finish, or a smooth and modern Anthracite Dura finish. Additionally, there is a huge range of 32 different optional standard colour finishes, including Heritage and Metallic colours, and the Centre Ribbed design can also be manufactured in a Medium Oak foiled finish. With this range of choices, there will be something to suit every garage. 

Handles
This door is not designed for manual operation and does not come with a handle, regardless of if a motor is selected or not.  

The inbetween installation kit uses the Executive framing kit as standard, this is a 100mm wide aluminium box section frame on 2 sides and reduces the structural opening width by at least 200mm on the width as well as either 100 or 130mm on the height - this gives the ordering dimensions. A tolerance should always be allowed for in these calculations and we recommend between 5-10 mm all round.

Width measurements should be taken in 3 places as a minimum and take the smallest measurement as it is inbetween. Take off 10-20mm on the width and then 5-10mm for the height from floor to lintel, again measured in 3 places to work out your ordering sizes.

Please note: panel configuration may vary from online images shown depending upon height of door. We strongly advise that you check a mock up diagram prior to the door going into production.

The Seceuroglide Elite Sectional Doors are suitable for openings up to 5 metres wide:    
Manual or electric operation 
Minimum side room required: 85mm
Actual drive through height (manual): DOH - 230mm
Actual drive through height (electric): DOH - 20mm
Minimum head room required (manual): 100mm
Minimum head room required (electric): 130mm

Installation Instructions are provided with every door.

Elite Fitting Instructions PDF >

All Seceuroglide products are guaranteed against defect of material or workmanship by SWS UK subject to correct installation, maintenance and operation for a period of 2 years from the date of purchase.

In addition Medium Oak textured woodgrain finishes carry a limited 10 year guarantee.

The NRG Black Edition electric motor carries a 7 year guarantee*

*7 Year warranty available on the motor if registered.

The inbetween installation kit uses the Executive framing kit as standard, this is a 100mm wide aluminium box section frame on 2 sides and reduces the structural opening width by at least 200mm on the width as well as either 100 or 130mm on the height - this gives the ordering dimensions. A tolerance should always be allowed for in these calculations and we recommend between 5-10 mm all round.

Width measurements should be taken in 3 places as a minimum and take the smallest measurement as it is inbetween. Take off 10-20mm on the width and then 5-10mm for the height from floor to lintel, again measured in 3 places to work out your ordering sizes.