The Seceuroglide Sectional Door design makes the most of the space both inside and outside of the garage, by rising vertically allowing you to park right up to the door. The Georgian is a beautiful traditional design, great for period style properties but with all the added benefits of a modern sectional door. Manufactured in the UK, the excellent quality, value, ease of installation and use and fast manufacturing times make these sectional doors an outstanding choice.
- Made to Measure Sizes at no extra cost
- Insulated 40mm double skinned panels
- Simple side spring assembly
- Easy DIY installation
The Seceuroglide Sectional Garage Door creates a stylish feature that is sure to enhance the look of your home but also the security and insulation. The Georgian sectional garage door by Seceuroglide is a traditional style with square panels, perfect for period style properties. It is produced in a woodgrain embossed surface finish, mimicking a painted timber door but with all the low maintenance and high spec benefits of a modern steel sectional door.
The Seceuroglide sectional garage door has a 40mm thick insulated steel panel manufactured to the highest specification, filled with PU foam - this along with the high grade rubber weather seals on all sides ensures a very high level of insulation, meaning an energy efficient and money saving door. This also goes hand-in-hand with security - the thick panels and the sophisticated locking system ensures peace of mind for you and your whole family. Whether you have a manual or an automated door you will be totally protected from intruders.
The Sectional garage door design makes the most of your driveway and garage; vertical operation ensures you can park right up to your door on either side and use your entire driveway. The Elite requires just 130mm headroom for motorised operation and 100mm for manual operation.
The standard finish is a traditional style White woodgrain embossed finish, or you can choose from a huge range of 32 different optional colour finishes, including Heritage colours such as Chartwell Green. With this range of choices, there will be something to suit every garage.
*Remote Controlled Electric Operator
Please note that if you opt for a manual door with handles you will LOSE approximately 230mm clear passage drive through height. Should you require any clarity or would like us to double check any technical specs or measurement diagrams, please do not hesitate to contact us.
The inbetween installation kit uses the Executive framing kit as standard, this is a 100mm wide aluminium box section frame on 2 sides and reduces the structural opening width by at least 200mm on the width as well as either 100 or 130mm on the height - this gives the ordering dimensions. A tolerance should always be allowed for in these calculations and we recommend between 5-10 mm all round.
Width measurements should be taken in 3 places as a minimum and take the smallest measurement as it is inbetween. Take off 10-20mm on the width and then 5-10mm for the height from floor to lintel, again measured in 3 places to work out your ordering sizes.
The Seceuroglide Elite Sectional Doors are suitable for openings up to 5 metres wide: 
Manual or electric operation
Minimum side room required: 85mm
Actual drive through height (manual): DOH - 230mm
Actual drive through height (electric): DOH - 20mm
Minimum head room required (manual): 100mm
Minimum head room required (electric): 130mm
Installation Instructions are provided with every door.
Elite Fitting Instructions PDF >
All Seceuroglide products are guaranteed against defect of material or workmanship by SWS UK subject to correct installation, maintenance and operation for a period of 2 years from the date of purchase.
In addition Golden Oak textured woodgrain finishes carry a limited 10 year guarantee.
The NRG Black Edition electric motor carries a 7 year guarantee*
*7 Year warranty available on the motor if registered.
The inbetween installation kit uses the Executive framing kit as standard, this is a 100mm wide aluminium box section frame on 2 sides and reduces the structural opening width by at least 200mm on the width as well as either 100 or 130mm on the height - this gives the ordering dimensions. A tolerance should always be allowed for in these calculations and we recommend between 5-10 mm all round.
Width measurements should be taken in 3 places as a minimum and take the smallest measurement as it is inbetween. Take off 10-20mm on the width and then 5-10mm for the height from floor to lintel, again measured in 3 places to work out your ordering sizes.
Our Promise
We pride ourselves on our customer service and are always happy to help